MICROBOT MOTOR DRIVER

It is a high voltage, high current dual fullbridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays,solenoids, DC and stepping motors. Microbot Easy Motor Controller Microbot. To ensure safely operating condition you can measure the motor current absorption of each motor; this allow to avoid stall conditions. Do you need an offer? To enable or disable each channel independently of the input signals there are provided two enable inputs E1, E2 positioned on the front of the board; motor velocity regulation is obtained applying to these pins a PWM signal with a 20KHz max.

Uploader: Mutaur
Date Added: 12 December 2008
File Size: 18.91 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 62021
Price: Free* [*Free Regsitration Required]

The Easy Motor Controller microbor two separate power supplies, one for the motor and the other one for the logic part; the latter can be pulled out through a jumper directly from that of the motor or alternatively from the BEC circuit of the RC receiver.

By using our services, you agree to our use of cookies.

We would like to ask you to consider this in your order planning! The sensor is the integrated circuit TCN75A and you can refer to its datasheet to better understanding its communication protocol.

This board also provides direction LED indicators for both channels and this is very usefull during setup stage to verify the firmware behaviour; the led indicators work also without appling a real motor to the output. Specifications Supply voltage 7 – 30V Supply current logic 24mA typ.

This board also provides direction LED indicators for both channels; this is very usefull during setup stage to verify the firmware behaviour also without appling a real motor to the output. Maggiori informazioni Read more. Add to project More from Microbot. The maximum supply voltage supported by this board is 30V.

  ALS SC4000 DRIVER DOWNLOAD

On this shield the selection of the power source for motor outputs is accomplished by a jumper.

The Driver IC may become very microgot when working with current more than 1A. Its use is very simple and you do not have to do anything, the type of input used is detected automatically motpr the board is powered. To enable or disable each channel independently of the input signals there are provided two enable inputs E1, E2 positioned on the front of the board; motor velocity regulation is obtained applying to these pins a PWM signal with a 20KHz max.

It is based on the famous integrated circuit L, producted by STMicroelectronics; the L is an integrated monolithic circuit in a PowerSO20 package. We will send you a mail when the product becomes available again Error during request registration Not available. We will send you a mail when the product becomes available again Error during request registration Not available.

Dual DC Motor Shield

The maximum supply voltage supported by this board is 46V. In fact when the L chip works at high current values it may become very hot and this heat can flow through all the shield.

By using our services, you agree to our use of cookies. Maggiori informazioni Read more. To prevent board damages, all driver lines are diode protected from back EMF.

Microbot Easy Motor Controller

All orders after this time will be shipped again from The Dual DC Motor Shield is a shield that has been projected to enable an Arduino board to drive two brushed DC motors or one 4-wire two-phase stepper motor, controlling the speed and direction of each one independently.

  COMPAQ NC2400 WIFI DRIVER

This powerfull DC motor driver can drive motor up to 30V and 4Amax. View additional product data. For the I2C communication, there are two different slave addresses selectable through a jumper, and in this way it is possible to use two Easy Motor Controllers mcirobot the same serial line, and then control them by using a single external controller.

Dual DC Motor Shield

It is a high voltage, high current dual fullbridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays,solenoids, DC and stepping motors. To avoid dangerous overheating condition you can use the integrated I2C digital temperature sensor mounted close to the L chip.

Cookies help us deliver our services. To optimize the response to RC commands you also have the calibration function on the receiver signals. Moving the jumper from one side to the other the power source can be changed. Microbot Easy Motor Controller.

The minimum supply voltage allowed is 7V, so you can use also two-cell LiPo batteries 7. The logic of the Dual DC Motor Shield is powered directly from mifrobot Arduino board, whereas motor outputs can be powered both from Arduino Vin pin or from external power source, even if it is strongly encouraged to use external power supply.